Home > Water Heater > Why Is My New Hot Water Heater Not Working

Why Is My New Hot Water Heater Not Working

Contents

can I do anything about this ? Apparently the rod should have been changed 2 years ago. I understand this is important as it could have blown up. Resetting either the circuit breaker or the high-temperature cutoff may resolve the problem, but the fact that they were tripped in the first place may indicate an electrical problem. navigate here

Close the drain valve and fill the tank before switching on the circuit breaker. You can flush out the tank yourself, although by the time you’re hearing this sound the sediment chunks may be too large to pass through the drain valve. Gary Shan i have a gas water heater in a rental and is used almost exclusively for the shower in Texas -yesterday after running a bath I noticed no more hot Turning on any tap momentarily reduced the pressure to system pressure (50 degrees F). http://www.whirlpoolwaterheaters.com/owner-center/installation-video-guides/electric-installation-videos-guides/troubleshooting-repair/

Gas Water Heater Not Working

If the connection to the fuse had a 0.5 ohm resistance, the current would cause 10 watts to generated at the fuse (Think a small light bulb's worth). Though many gas utility companies will make a free house call to solve problems with a gas water heater’s gas supply to the tank, you're on your own when it comes Water heater manufacturers recommend a temperature setting of no higher than 120ºF. Copyright © 1995-2016 DoItYourself.com Inc.

That would cause the connection to get very warm. ReviewsWATER HEATERSElectric Water HeatersNatural Gas Water HeatersLiquid Propane Water HeatersLearn More (Gas)6th Sense™Cost of OperationHow Gas Water Heaters WorkBasic Product FeaturesModel Numbers GuideFAQsGlossaryLearn More (Electric)Standard Electric Water Heaters6th Sense™ Water HeatersCost Testing Thermostat for Power with Voltmeter If the unit is powered with the correct voltage, and still does not produce any hot water, the upper heating element has probably burned out. How To Tell If Electric Water Heater Is Working I have a similar problem Larry Hinton It's most likely the thermal couple needs replaced.

I didn;\' know you already had the answer. Electric Water Heater No Hot Water This all started happening over the last weekend. Remember Me? Can someone please give me advise on what to do to fix this problem Don Vandervort, HomeTips Sounds to me like a defective pressure relief valve, but I'd like to have

The fix is straightforward, and replacement elements are inexpensive ($8 to $20) and readily available at home centers, hardware stores and appliance parts dealers. Electric Water Heater Thermostat If you need service on any Rheem water heater or room heater ring our 131 031 number and you will be connected to the nearest Rheem Service office. We need more info if your situation falls outside of those answers. The Installation Instructions require that a hot water faucet be opened and the hot water allowed to run full for at least three minutes before turning the power on.

Electric Water Heater No Hot Water

I hope someone can help me. Help those who take the time to help you and save you money.***For a super detailed understanding of how the thermostat operates, watch this video:https://www.youtube.com/watch?v=nifLZ...Excellent video explaining how to inspect your Gas Water Heater Not Working To check for power, turn the circuit breaker marked "water heater" off (or remove fuses). My Water Heater Is Not Heating Water where your power comes in at the upper thermostat, read from line to line.

The switch on the thermostat itself hasn't been tripping again, but the circuit breaker is. http://nadrp.com/water-heater/why-the-water-heater-is-not-working.html Possibly the upper one overheated if it was exposed to that air. and by the way, the reason the lower element would not heat is because the upper thermostat is designed to give the upper element priority. Replacement is best left to an appliance repair person or a water heater specialist. 5Smell for gas. Water Heater Reset Button

SIGN UP Please enter valid E-Mail Address FOLLOW US Subscribe Give a Gift Advertise With Us Customer Care Content Submission Contact Us Privacy Policy Terms of Use © 2016 HOME SERVICE That will give clues on how to proceed if what I've already written doesn't cover it. Do you see any moisture around the elements... http://nadrp.com/water-heater/water-heater-not-working-right.html To minimize corrosive minerals through ionization, water heaters have a magnesium or aluminum anode rod, inserted through the top of the tank.

Back to Top Replace an element Photo 4: Remove the bad element Drain the water from the tank and unscrew the old element using a heating element wrench. Electric Hot Water Heater Not Working After Power Outage Zero out your ohm meter and disconnect the wires to the elements. I'm am baffled, how is air getting into the hot water line?

The quickest and most obvious first step is to adjust the temperature dial on the front of the water heater, wait a little while, then check the water temperature at a

The chances are good that some scale from mineral deposits chipped off the inner surfaces of pipes and partially clogged the pipes somewhere. If I change the fuse it works to heat it back up and then blows again. Check in the same way as the upper element for 240. Whirlpool Electric Water Heater Troubleshooting Also, if the high limit didn't click when you pressed it, the limit might be working OK and not be the problem.

Answering simple questions, I will always continue to do, but I have adopted a new policy in which I ask any viewer who seeks, "An Advanced Level Of Help" to post HIRE A PLUMBER OR ELECTRICIAN. I relit the pilot light and it stayed on after the fan started running. http://nadrp.com/water-heater/water-heater-rv-not-working.html Eventually you end up with the wire, the fuse socket, etc getting extremely hot (but not enough to blow the fuse).

I understand this is air in the water and it clears fairly quickly. Hope this helps -- Sky_Tech Q4: Thanks Sky_Tech, I`ll check the fuse box this weekend (the water heater is in a country home that we use only on weekends). (2/10/10) Electric Reconnect the wires, making sure the connections are tight. I reset the breaker again and it was fine.

AFTER you establish that there is power being supplied to the water heater, ALL remaining tests are done with the POWER OFF to the water heater.You will need a phillips & This second one repeatedly pops the reset button on the heater (I have never known it to pop the circuit breakers in the house panel). Often when a high limit trips, it's a symptom of another problem. I live by myself but I shower regularly, run my dishwasher, my washing machine, etc.,etc.

BOTH of them if there is more than one? 04-26-08,11:49 AM #6 cheyne1 Member Join Date Apr 2008 State NH Posts 6 Thanks for your help. Thank you. Because the first element I removed was rated 4500 watts, I replaced it with a basic cheap 4500-watt one. The service man thought my water softner may be backflushing into my water heater when it recharges at night.

Sign in to add this video to a playlist. If the problem is only with the hot water, in most cases the odor is caused by a reaction between the hot water heater’s anode rod and water that has a All rights reserved. It worked perfectly up until recently.

Then suddenly the sound of flushing occurs and the loud noise wears off…only for it to start again. Have twice replaced the 240-volt single element on a 10-year-old State 52-gallon heater which is rated for 5500 watts. There are many things you can do to help. The closer you live to a water tower the better the chances of your water pressure.

Not enough hot water (or no hot water)?