Home > Water Heater > Water Heater Igniter Not Working

Water Heater Igniter Not Working


The thermocouple should be embedded in the flame and tighten correctly - first hand tighten it and then use the wrench for additional 1/4 turn. Sometimes, carbon deposits can build up on the pilot and eventually create a restriction. Pull out the old thermocouple. diy plumbing videos 13,297 views 4:21 Loading more suggestions... have a peek at this web-site

Make sure the electrode is not broken... Make sure that the tank is completely filled with water before lighting the pilot light. Sign in 1,290 81 Don't like this video? Request unsuccessful.

Water Heater Igniter Won't Spark

Sign in to add this video to a playlist. While continuing to hold down the pilot button press down on the igniter button three or four times. just the device itself not running new wires? 18 answers The ceiling fan has power but the lights don't turn on and the blades don't spin when I pull the chains.??? If you do, leave the house and call your gas utility.

  1. When trying to light the heater be sure to put the gas valve on the water heater in the 'Pilot' position and hold down on the pilot button.
  2. Came home yesterday and … Pilot light won't stay lit when you turn knob from pilot to on, it goes out as soon as the knob pops up before you can
  3. FIND a local water heater expert and get a FREE quote if need a help.
  4. The igniter works only sometimes.
  5. Causes, problems and troubleshooting pilot light Pilot light goes out due to condensation Most of today's energy efficient water heaters will produce a certain amount of condensate.
  6. Published on Feb 18, 2014This video provides step-by-step instructions for replacing the igniter and flame sensor on AO Smith gas water heaters.
  7. How to fix the water heater when the light goes out, does not light, won't stay lit, pilot flame is too small or too large.
  8. Where is my model number?
  9. Loading...
  10. If you have a natural or propane gas water heater, chances are the pilot has gone out.

Otherwise, if the pilot light is not functioning properly, you won't have hot water. Parts Thermocouple Please enter your model number so we can show you the part that fits your exact model Where is my model number? Your model number is on a plate, in one of these locations: Handy tip -Make it easy on yourself! Water Heater Pilot Won't Spark I ended up replacing the hot water tank in total.

Cause 1 Igniter Some water heaters use an igniter to ignite the gas. Water Heater Piezo Igniter To determine if the igniter is defective, first make sure the igniter is getting voltage. Make sure the wire is connected at the bottom of the push button that makes the igniter spark. http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Water-Heater/175---/Water-heater-not-lighting I guess I have to put up the disclaimer.

Sign in to add this to Watch Later Add to Loading playlists... Electronic Ignition Water Heater Won't Light If the thermocouple does not detect a flame, the ignition process will stall, and the burner will not light. You'll get your hot water going without waiting for a pro to show up and save the cost of a service call. If the pilot cannot be cleaned, replace it.

Water Heater Piezo Igniter

Replacement is an easy DIY repair. steven lavimoniere 182,471 views 18:10 Hot water tank pilot goes out - Duration: 3:10. Water Heater Igniter Won't Spark Faulty piezo igniter. Water Heater Igniter Doesn't Work Rating is available when the video has been rented.

I would try the igniter several more times. http://nadrp.com/water-heater/when-hot-water-heater-is-not-working-well.html HouseImprovements 94,529 views 6:51 (Read Descriptions for IMP Info) Volume 1 Introduction: problem & Troubleshooting - Gas Water Heater - Duration: 4:49. Check the wire connection is it properly tightened. Loading... Water Heater Piezo Igniter Won't Light

Sergio Cordova 550,535 views 8:18 3 Different Ways to Clean a Flame Sensor - Duration: 5:06. It was burning normal until then (pilot flame shooting to the … Downdraft in chimney when attic fan is running Not rated yetWe had a new attic fan installed. When troubleshooting the lighting problems, it is recommended to test it first. http://nadrp.com/water-heater/water-heater-piezo-igniter-not-working.html When I tried your slower method, it started up almost right away.

RepairClinic.com 127,786 views 4:56 Water Heater Pilot Light Keeps Going Out Honeywell Valve - Duration: 16:06. Hot Water Heater Pilot Won't Light Yes No Sorry, something has gone wrong. The proper air supply should be delivered when the unit is installed in the small confined space.

I was told tankless heaters were very expensive and so elected to have a traditional tank installed.

No hot water? Loading... If the water heater is installed in an attic, an excessive heat (above 120 C) could be another reason. Water Heater Igniter Got Wet Up next A.O.

Your model number is on a plate, in one of these locations: Handy tip -Make it easy on yourself! Please try again later. Please try again later. have a peek here Pilot light will not remain lit When troubleshooting pilot light problems such as when it does not stay lit, keep in mind that there are often different causes for this and

Sign in to report inappropriate content. If the spark electrode won’t produce sparks, it is likely defective. It might even be under warranty. If the pilot light tube and its orifice are clogged you should clean them.