Home > Ice Maker > Whirlpool Infrared Ice Maker Not Working

Whirlpool Infrared Ice Maker Not Working

Contents

All rights reserved. Even the whirlpool ICE maker service sheet that came with the unit indicated the issue as defective boards. Part Testing Watch this helpful video to determine if this may be the cause of your issue. I ordered a new set of controller boards for the level controller and the system began working a day before the boards arrived. Check This Out

Reply Chic Posted on July 16, 2015 OK, then just change the words "control beam" to read "status LED" and the info in the post will still apply. A very simple and easy way to see infrared light by using a digital camera.In the video clip I show you how it works. The most co... So in 24 hours, the icemaker should make approximately 80-175 cubes.

Whirlpool Ice Maker Reset Button

Thank you very much!What a great website and what excellent service! Chic Posted on July 21, 2015 SN SS5156298 Jon Posted on July 18, 2015 I get a double blink with the flapper open, and when I hold it closed I get Sign in to make your opinion count.

Reply Ryan Posted on July 21, 2015 Do you have the serial number of your refrigerator? The optical boards function the same however, their diagnostic functions differ. That made me understand it wasn't electrical or mechanical. Whirlpool Conquest Ice Maker Not Making Ice Proceed to step 2.

We cannot express how important it is to read the manufacturers instructions that are included with every product you buy and use. Whirlpool Conquest Ice Maker Not Dispensing Ice Choose your language. Open the Freezer door for and activate the freezer door switch 3 times within 10 seconds (see Figure 6 above). 6. AppliancePartsPros 55,290 views 8:25 Refrigerator Ice Dispenser Chute Door (part #WP2180353)-How To Replace - Duration: 6:38.

I was so surprised and thankful that because we live in the same town you personally delivered the part to me! W10757851 Note to be certin that the jumper stays in place or the test will fail. 3. If the icemaker module is defective, the ice maker won’t make or dispense ice. Sign in Share More Report Need to report the video?

  1. I did the repair right before bed so I didn't get to hear the first batch of ice drop, but it was great to wake up this morning and look in
  2. The bottom mounting bracket on the old icemaker must be reused. $104.13 Quantity: In Stock › Suggested tools Multi Screwdriver RepairClinic Item #3527472 $14.95 Nut Driver RepairClinic Item #3527674 $5.45 Same
  3. Find out more » Total: $65.99 Add to Cart Install Help Watch this helpful video to determine how to install your part.
  4. But from start to finish, it took me about 25 minutes to complete the job!
  5. Figure 6 - Activate Freezer Light Switch 3 Times 5.
  6. In addition to the step by step pictures and details to change those boards, you will to need to get replacement optical boards.
  7. The optics is just two sensors, one on each side of the freezer and when ice gets high enough to block the sensors it cuts the icemaker off.

Whirlpool Conquest Ice Maker Not Dispensing Ice

If the light blinks once followed by a one second delay, the optics are bad and needs replacing. http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Refrigerator/53-5-620905-/Whirlpool-Refrigerator-ice-maker-not-working Reply ibeck Posted on September 13, 2015 Did the optics board test and checked out good. Whirlpool Ice Maker Reset Button Did I stumbled on a "reset" or optics reboot? Whirlpool Conquest Ice Maker Parts If you want to avoid any delay, make sure your PayPal email address is correct.

Could there be grime or frost on ether the emitter or receiver board windows that may block the light beam’s round trip? his comment is here It sounds like your optic boards are most likely working correctly. If you realize that it was not current when you confirmed your PayPal contribution, please send me an email ([email protected]) NOTE: Microsoft's Outlook Express is sometimes set not to allow viewing Loading... Kitchenaid Ice Maker Sensor

Make sure the ice maker control is turned "ON". Reply Oz Posted on July 1, 2015 Kitchen aide superba Mod# KSC25INSS01 No ice. I thought I was going to break it or pull the wires out. this contact form The most...

Appliance parts online, right part, best price and fast shipping. Whirlpool Conquest Ice Maker Optics Parts Ice Level Control Board for your Whirlpool Refrigerator RepairClinic Item #3452789 Refrigerator ice level control board. I purchased your on-line troubleshooting guide and used it to diagnose the problem.

Reply Denise Posted on February 19, 2015 So it's either a frozen water line, water inlet valve, optic board or a bad ice maker.

Return From Whirlpool Icemaker Repair Guide Appliance-repair-it.com is a free service but it cost to keep it up and running. Then I tired it with my tv remote and a couple other infrared remotes we had around the house. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. Whirlpool Infrared Sensor Blinking Once the mold reaches the proper temperature, the icemaker ejects the ice cubes and refills the ice mold with water.

There is an optic board test that should work on all models of this ice maker after 2002. Hold flapper it's constant. Thanks and have a good day!!John Murphy - [email protected] ICEMAKER REPAIR WORKED!Duane, I have to say I was a little skeptical about buying your icemaker repair guide, however when I saw navigate here If the ice level control board fails, the ice maker will stop making ice. $213.92 Quantity: In Stock › Same Day Shipping Order by 8:00 PM ET, this part ships TODAY!

Open the freezer door and observe the red status light next to the ice maker’s on/off switch. Close the Freezer door for a minimum of 10 seconds. It is a very easy and quick fix...if you can determine from the instructions above that your optical boards are bad, then you will have no problem replacing the optic boards If the icemaker module has ejector blades, check to ensure that ice cubes are not stuck in the blades.

To repair this issue with the ice maker was quoted by our local Sears repair department to cost $230. This video demonstrates how to test a two terminal swit... Result: The red status light should be steady on. The harvest part of the cycle is when the fingers are scooping the ice out of the ice maker.

pause. Within the instructions, I show you how you can get a set of boards with a 1 year warranty and a guarantee that if it doesn't fix your problem, you can Then separately I tried holding flapper door and light switch off and the Led stays completely off. All other functions in the fridge and freezer appear to work fine with the exception of the icemaker and emitter board. - Is there a separate power board? - Kitchen aid

If you are unable to read the attachment that is automatically sent to you once you donate via PayPal (or you do not see an email reply within 10 minutes), try So I started reassembling everything about 9pm that night. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next.