If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve. Installed the part and had ice in no time. But finally I got the wire harness to separate. The $23 CDN was well worth the saving difference from a $90 call out from the service guy. Check This Out
Did you figure out the problem? Board Kit, AP3137510 « Last Edit: January 10, 2008, 12:13:21 PM by AJ » Logged technician VIP Member Member Since: Jul 2007 Posts: 2 Re: How to see if your Whirlpool Similar topics Video: Whirlpool In-Door Ice Maker Fill Cycle Started by AJ Replies: 3Views: 13083 September 23, 2008, 05:37:19 PM by Al Capone Video: How to make your Whirlpool ice maker This part can be found at AppliancePartsPros.com.
ApplianceAdvice 77.574 visualizaciones 4:30 Troubleshooting Ice maker repair Whirlpool Kitchenaid Whirlpool - Duración: 8:13. with freezer door open i get 2 blinks. If the icemaker module is defective, the ice maker won’t make or dispense ice.
Reply Ralph Fay Posted on February 7, 2016 what was the part you had to replace in addition to the optics Reply Dina Posted on January 16, 2015 I've replaced the RepairClinic.com 71.313 visualizaciones 3:02 Ice Maker Not Working? – Whirlpool Refrigerator Ice Maker Module Replacement (Part #W10190935) - Duración: 2:03. Water Inlet Valve Testing Refrigerator not making ice or not dispensing water? Whirlpool Conquest Ice Maker Parts Thanks again,Todd & Kathy Savenko - [email protected] (remove NOSPAM for valid email address) Ice Maker Repair - Why wait?
Reply Bob Posted on January 1, 2015 Kay- Same problem here, did you ever get it resolved? Whirlpool Conquest Ice Maker Not Dispensing Ice When I originally wrote about the jumper wire test I didn’t intend on it to be used on refrigerators with the ice-bin mounted on the door but it should work if Each filter provides 200 gallons of filtered water and should be changed every 6 months to ensure proper contaminant removal and flow rate. http://appliancejunk.com/forums/index.php?topic=44.0 Elige tu idioma.
Don't I need to keep the new IR boards since the old ones failed the diagnostics previously? W10757851 Start here All parts purchased from AppliancePartsPros.com have 365 day no questions asked return policy. I think the part is called the "flipper"? Hold flapper it's constant.
Made sure it's on first. Parts Icemaker Module for your Whirlpool Refrigerator RepairClinic Item #961550 Repair kit. Whirlpool Ice Maker Reset Button Open the freezer door (make sure that the freezer door has been closed for a minimum of 10 seconds prior to opening the door). Whirlpool In Door Ice Maker Not Working I was about to pay someone $275 to come and fix the ice maker.Thank you very much for saving me $193.51.
The rest was cake. his comment is here Just wanted to say thanks! Cause 2 Water Inlet Valve The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. This is the test procedure for this Whirlpool icemaker. 1. Kitchenaid Ice Maker Sensor
Next, with the freezer door open, hold down the flapper door on the left hand side to un-block the optics beam. With the optics beam unblocked, the status LED should light But from start to finish, it took me about 25 minutes to complete the job! Reply wahid Posted on May 26, 2015 Hello, Where I can buy mine prt NO 2198586? this contact form You may re-enable this once you have the chance to get your login and password from the email attachment that is sent.
That's the 2 o'clock position from the right side of the so-called fridge, not sure which orientation is meant by 2 o'clock. Whirlpool Ice Maker Control Board A paper clip works really good for this.4. When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes.
No- If there is no ice in the mold take that jumper wire and place one end in the hole marked V and the other end in the hole marked L The most common... Thanks Reply Jose Posted on March 14, 2015 I have a kitchenAid which is not make ice. Whirlpool W10757851 Is there any ice in it?
Cola de reproducción Cola __count__/__total__ How To Troubleshoot A Whirlpool Modular Ice Maker With Optical Controls SamuraiRepairman SuscribirseSuscritoCancelar9.3409 K Cargando... B. To check the water line to see if it is frozen, you should remove the line from the water valve and blow through it. navigate here Within the instructions, I show you how you can get a set of boards with a 1 year warranty and a guarantee that if it doesn't fix your problem, you can
There is an optic board test that should work on all models of this ice maker after 2002. What does that mean (Harvest mode)? It did the same as few days ago and another punchin/shakedown worked. Inicia sesión para que tengamos en cuenta tu opinión.
AppliancePartsPros 47.855 visualizaciones 3:32 Kenmore Ice maker replacement repair DIY - Duración: 2:49. While waiting for the replacement we removed the ice solenoid, and the freezer made ice continuously. Disconsolate Kevin Albemarle, NC Reply With Quote January 2nd, 2007,01:36 AM #8 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, It took about 20- 30 minutes to get everything put together and back in the freezer (I was on the phone while doing it).
Reply Ryan Posted on January 22, 2015 The light switch cannot be pressed in when doing the test. Even the whirlpool ICE maker service sheet that came with the unit indicated the issue as defective boards. It worked on all of them.Cool little trick... If you have a yahoo.com email address, make sure to check your spam folder...seems like yahoo.com likes to stick my emails in there.
Remove the three Phillips screws on the right hand side. Inicia sesión para añadir este vídeo a una lista de reproducción. That would mean lots of time, effort, and $150, for nothing. If you would like to get a set of optic boards, the cost would be $19.99 for the instructions plus $79.99 for the optic boards plus a $20.00 refundable deposit (this
Or, if you don't use PayPal, then your payment can be sent to: Absolute Technologies, Inc.Attention: Ice Maker RepairPO Box 601Holly Springs, NC 27540 Please include your email address so thatyour Duane,I received the motor assembly today and installed it quickly with no issues.