Home > Ice Maker > Whirlpool Gold Freestanding Ice Maker Not Working

Whirlpool Gold Freestanding Ice Maker Not Working

Contents

Use a vacuum cleaner to remove dirt from the bottom of the unit compartment. 5. Ascending Order Descending Order Note: when sorting by date, 'descending order' will show the newest results first. Make sure the water supply is properly connected to acold water supplyand the watershutoff valve is fully opened. Remove the valve stem from the Schrader valve on the access fitting. Check This Out

Close Yeah, keep it Undo Close This video is unavailable. Repeat the "plucking" a few times until the strings are "moderately" tight, "moderate" as in playing a low note when you pluck them like a guitar string, not so tight as Last Jump to page: Threads 1 to 20 of 100 Forum: Undercounter / Freestanding / Stand Alone Ice Makers Problems with your Undercounter / Freestanding / Stand Alone Ice Maker? Not as long as you might think. http://www.truetex.com/icemachine.htm

Whirlpool Stand Alone Ice Maker Troubleshooting

This is a good time to clean the grid with acid cleaner if it has lime encrustation or other debris. The cut-out screw sets the colder temp for the harvest trigger, the cut-in screw sets the warmer temp to end the harvest. Loading... Again, the goal is only to have the wire tight enough to not sag.

Loading... The performance specifications on the "Service and Wiring Sheet" indicate that the machine should harvest a medium-thick (about 0.45") slab of ice every 18 to 22 minutes under favorable conditions (ambient It also replaces the spring-clip type grid (difficult to repair) described next. Kitchenaid Undercounter Ice Maker Manual I use a propane/air TurboTorch and insulating pad to get the joint up to temperature and soldered very quickly, with a minimum of heat loss to the rest of the system.

ApplianceVideo.com 7,409 views 1:01 EdgeStar - IB120SS Undercounter Ice Maker Service Provider Support - Duration: 22:30. Black electrical plug with two brass prongs (same as previous type). During harvesting, the water valve opens to refill the recirculating reservoir and flush the "used" water out via an overflow drain, while the recirculation pump stops. (The freezing process removes minerals

Carefully pour the entire 1/2 gal.

You are not loosening a soldered joint or fitting under pressure, just the mechanical attachment of a bracket. Kitchenaid Undercounter Ice Maker Service Manual Bottom of slab and underside of evaporator (with capillary sensing tube to thermostat) are well below freezing. Apply and withdraw the flame in cycles to keep the area just above the solder free-flow temperature, and keep the overall time to the minimum needed to get a good joint. Does your water filter need to be replaced?

Kitchenaid Ice Maker Reset

Add your answer Sign in to answer a question 1 Answer from this member: If the compressor is running but no ice is being made and it feels warm inside, it http://www.shopyourway.com/questions/1075544 While the valve should seal completely, this is not necessary, if you apply an O-ring cap to cover the access port when you are not servicing the machine. Whirlpool Stand Alone Ice Maker Troubleshooting Sign in to make your opinion count. Kitchenaid Ice Maker Not Making Ice After Cleaning The blue "On/Off" l.e.d.

The KitchenAid models are designated KUIS155 and KUIS185 with suffixes for variations in finish style. his comment is here of hot water. This line-piercing valve will provide a 1/4" flare fitting, to which you can add an adapter for 1/4" flare to R-134a low-side quick-connect fitting. Sign in Transcript Statistics 524 views 0 Like this video? Kitchenaid Freestanding Ice Maker Troubleshooting

You can cut your own replacement rubber piece quite easily. Water inlet valve not putting enough water into water reservoir Water inlet valve not shutting off and dripping water into the reservoir during freeze cycle causing water temp not to drop. Suction-side pressure in the refrigeration unit declines to 6 to 10 psig. 10:00 Ice builds in thickness: Evaporator plate now fully covered with a thin layer of ice. http://nadrp.com/ice-maker/whirlpool-gold-refrigerator-ice-maker-not-working.html One source is Peer 627-4-2RS (catalog); another is / [[strings_.TITLE]] [[strings_.CONTENT]] [[strings_.SKIP_FEEDBACK_LABEL]] [[strings_.SEND_FEEDBACK_LABEL]] [[strings_.CLASSIC_YOUTUBE_LABEL]] Debug Show log entry Show visual element tree Copy Visitor ID Show logging window Toggle dark

Up next KitchenAid - Whirlpool IceMaker not producing or dropping ice cubes -KUIC15NRXS0_DR - Duration: 7:50. Kitchenaid Freestanding Ice Maker Not Making Ice If at the end of 30 minutes the mineral build-up has still not dissolved, turn the service control switch to the "OFF" position, and carefully drain out the cleaning solution. These connectors rarely fail, but when they do they are almost impossible to find.

Sign in to add this to Watch Later Add to Loading playlists...

Your question was published, help is on its way! On some models, the low-voltage transformer that powers the cutter grid also powers a bin light. Black electrical plug with two brass prongs. Kitchenaid Stand Alone Ice Maker SamuraiRepairman 22,997 views 6:23 Ice Machine Part 1 - Duration: 9:55.

You'll need all four of these spacers (I regret I do not sell these parts) plus the wire to perform the upgrade. ft. To Enter the Service Mode: Remove the reservoir drain cap and make sure the reservoir is empty. navigate here This is the most common grid type on the electromechanical machines, and easiest to repair.

After allowing the grid to soak for approximately 15 minutes, use a hard bristled brush to scrub the wire connectors and insulators around the edge of the grid. Check evap. I have published this information as part of my machine shop pages, because these repairs have to do with metal itself (nickel-chromium wire, solder), or with parts or suppliers closely associated Clean the exterior enamel surfaces and the gaskets around the door with warm water and a mild soap or detergent.

This is an easy repair, assuming you ruled out the loose bracket first. The hot gas solenoid and water valve solenoid are in parallel, so if the unit reverses during the harvest and rapidly warms the evaporator plate, then the controls are OK. The latest version of the electronically-controlled Whirlpool (and KitchenAid branded) machine (2007 and after) is described by Service and Wiring Sheet 2324311C. The ice slab rests on the heated wires, and the wires slice through the slab, first in one direction on the top layer of wires, then the perpendicular direction on the

If the machine has been turned off and sitting idle for a while, turning it on should not activate the water valve solenoid, it should simply start chilling, and if there Working... All other trademarks are owned by their respective companies.MSRP is Manufacturer's Suggested Retail Price and may not necessarily be the price at which the product is sold in the consumer's area. This is Whirlpool part number 386433 on my unit.

Sign in 46 6 Don't like this video?