RepairClinic.com 22,947 views 3:37 Ice Maker Repair - Duration: 7:48. Home Guides Home Home Improvement by Demand Media Home Guides » Home » Home Improvement » How to Check an Icemaker Solenoid How to Check an Icemaker Solenoid Verifying the functionality The control board then shuts off the ice maker. Use your smart phone to take a picture of the model number tag. http://nadrp.com/ice-maker/whirlpool-ice-maker-not-working-water-valve.html
Thank you for helping make our site better. 1-855-343-0066 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST 1-888-738-4871 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST Cart (0) Order Status Home Help Contact Instant Repairman™ Return any part for any reason with our generous 365-day return policy.In addition to providing replacement parts, RepairClinic.com offers free online troubleshooting information and DIY repair videos. Now what, Does that mean everything is working and it is the icemaker that is broken or clogged or something? Use your smart phone to take a picture of the model number tag. http://www.popularmechanics.com/home/how-to/a166/1276061/
Advertisement - Continue Reading BelowTo test the solenoid valve, use a multimeter (also called a volt-ohm meter). If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve. The electrical component that activates a valve to allow water to flow into the ice making area is called the solenoid. Rating is available when the video has been rented.
What Gives? References (1) Popular Mechanics: Repairing An Icemaker Water Valve About the Author Writing professionally since 2010, Amy Rodriguez cultivates successful cacti, succulents, bulbs, carnivorous plants and orchids at home. Now what do I do to get this solved, because buying ice sucks... Ice Maker Valve Replacement Before installing the back panel on the refrigerator cabinet, test run the icemaker.
Cause 6 Door Switch The door switch turns off the ice and water dispenser when the refrigerator door is open. When the ice level drops below the beam, the control board signals the ice maker to make more ice. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly. http://www.partselect.com/Refrigerator+test-water-valve+repair.htm The flow of water to the ice maker is controlled by a valve, which is activated by a solenoid.
If you don't, bring the valve to an appliance store and get a replacement. Refrigerator Water Shut Off Valve If so look above your ice maker for a black rubber spout that comes down from your freezer ceiling, that may be clogged with ice, try to run something up in Loading... If yours is a double solenoid water valve, it will have four wires.
Sign in to make your opinion count. http://nadrp.com/ice-maker/whirlpool-ice-maker-not-working-water.html The meter should read in the range of 200 to 500 ohms. Putting some electrical tape around each is a good preventative measure.If your ice maker is removed, place a cup, can or small bowl under the black supply hose located above the Angela Gottschalk 905,952 views 3:08 Refrigerator Water Inlet Valve (part #W10408179)-How To Replace - Duration: 9:55. Ice Maker Water Valve Leaking
Top 6 Reasons Refrigerator Runs Constantly? The complete ice maker is a good value when you consider the additional troubleshooting time and the additional assembly time. I'm really hoping that the thousands of replacement modules have a revised design, or else we'll all be back to buying new modules in the next few years. Source Label the wire placement on the water inlet valve before disconnecting the wires.
Use a screwdriver or nutdriver to remove the rear lower access panel from the refrigerator's back. Refrigerator Water Supply Valve I am moving on to the module (Ice Maker, right?) tomorrow and removing it from the freezer to see if anything is clogged. If the icemaker switch does not have continuity, replace it.
Loading... Be sure to label each wire so that you know where to reconnect them later. This 100 multiplier mode in the device will provide the correct ohm units during testing; you may see unusual display numbers if you have the device at a different multiplier mode. Samsung Water Inlet Valve Replacement The valve requires at least 20 psi to function properly.
With Jake's direction, I decided to properly troubleshoot my icemaker. Rinse the filter clean, reassemble the valve and install it. Then gently pry the screen out with a small screwdriver. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly.
Use a wrench to loosen the flare nut on the brass fitting on the inlet side of the valve (above). With the multimeter's probes touching the solenoid's contacts, you should get a reading between 200 and 500 ohms. If you have a refrigerator that dispenses drinking water, the valve has a second outlet tube and solenoid. Enter Your Zip Code: © 2016 QuinStreet, Inc.
This optional refrigerator accessory automatically generates ice by using an electrical switch circuit. An icemaker valve costs about $30 to $50 from the manufacturer or an appliance parts distributor. Up next Refrigerator Ice Maker Not Making Ice | www.goodappliancesuperstore.com - Duration: 3:08. Place a container under the valve to catch the small amount of water that will spill from the valve and tubing.
These are all signs of a malfunctioning water valve. JPTL, I appreciate your input and you are right, I am just trying to be as methodical as possible to rule things out before I take the $90 plunge... Loading... Firmly pull the connectors off of the terminals (do not pull on the wire).